- NAME
- timerate — Calibrated performance measurements of script execution time
- SYNOPSIS
- DESCRIPTION
- -calibrate
- -overhead estimate
- -direct
- EXAMPLES
- SEE ALSO
- KEYWORDS
timerate — Calibrated performance measurements of script execution time
timerate script ?
time? ?
max-count?
timerate ?
-direct? ?
-overhead estimate?
script ?
time? ?
max-count?
timerate ?
-calibrate? ?
-direct?
script ?
time? ?
max-count?
The
timerate command does calibrated performance measurement of a Tcl
command or script,
script. The
script should be written so that it
can be executed multiple times during the performance measurement process.
Time is measured in elapsed time using the finest timer resolution as possible,
not CPU time; if
script interacts with the OS, the cost of that
interaction is included.
This command may be used to provide information as to how well a script or
Tcl command is performing, and can help determine bottlenecks and fine-tune
application performance.
The first and second form will evaluate script until the interval
time given in milliseconds elapses, or for 1000 milliseconds (1 second)
if time is not specified.
The parameter max-count could additionally impose a further restriction
by the maximal number of iterations to evaluate the script.
If max-count is specified, the evaluation will stop either this count of
iterations is reached or the time is exceeded.
It will then return a canonical Tcl-list of the form:
0.095977 µs/# 52095836 # 10419167 #/sec 5000.000 net-ms
which indicates:
-
the average amount of time required per iteration, in microseconds
([lindex $result 0])
-
the count how many times it was executed ([lindex $result 2])
-
the estimated rate per second ([lindex $result 4])
-
the estimated real execution time without measurement overhead
([lindex $result 6])
The following options may be supplied to the timerate command:
- -calibrate
-
To measure very fast scripts as exactly as possible, a calibration process
may be required.
The -calibrate option is used to calibrate timerate itself,
calculating the estimated overhead of the given script as the default overhead
for future invocations of the timerate command. If the time
parameter is not specified, the calibrate procedure runs for up to 10 seconds.
Note that the calibration process is not thread safe in the current
implementation.
- -overhead estimate
-
The -overhead parameter supplies an estimate (in microseconds, which may
be a floating point number) of the
measurement overhead of each iteration of the tested script. This quantity
will be subtracted from the measured time prior to reporting results. This can
be useful for removing the cost of interpreter state reset commands from the
script being measured.
- -direct
-
The -direct option causes direct execution of the supplied script,
without compilation, in a manner similar to the time command. It can be
used to measure the cost of Tcl_EvalObjEx, of the invocation of canonical
lists, and of the uncompiled versions of bytecoded commands.
As opposed to the time command, which runs the tested script for a fixed
number of iterations, the timerate command runs it for a fixed time.
Additionally, the compiled variant of the script will be used during the entire
measurement, as if the script were part of a compiled procedure,
if the -direct option is not specified. The fixed time period and
possibility of compilation allow for more precise results and prevent very long
execution times by slow scripts, making it practical for measuring scripts with
highly uncertain execution times.
Estimate how fast it takes for a simple Tcl
for loop (including
operations on variable
i) to count to ten:
# calibrate
timerate -calibrate {}
# measure
timerate { for {set i 0} {$i<10} {incr i} {} } 5000
Estimate how fast it takes for a simple Tcl for loop, ignoring the
overhead of the management of the variable that controls the loop:
# calibrate for overhead of variable operations
set i 0; timerate -calibrate {expr {$i<10}; incr i} 1000
# measure
timerate {
for {set i 0} {$i<10} {incr i} {}
} 5000
Estimate the speed of calculating the hour of the day using clock format
only, ignoring overhead of the portion of the script that prepares the time for
it to calculate:
# calibrate
timerate -calibrate {}
# estimate overhead
set tm 0
set ovh [lindex [timerate {
incr tm [expr {24*60*60}]
}] 0]
# measure using estimated overhead
set tm 0
timerate -overhead $ovh {
clock format $tm -format %H
incr tm [expr {24*60*60}]; # overhead for this is ignored
} 5000
time
performance measurement,
script,
time
Copyright © 2005 Sergey Brester aka sebres.